A Rowan company - serving Santa Rosa, CA
A remodeled primary bathroom with a soaking tub and a walk-in shower
Boral · Santa Rosa

Boral Bathroom Remodeling in Santa Rosa, CA

Free Estimate on SiteCalls Answered by a Live Person, 24/7Background-Checked TechniciansA Local Team in Santa Rosa
A remodeled primary bathroom with a soaking tub and walk-in shower
A freestanding soaking tub in a remodeled primary bathroom
A walk-in shower with large-format tile and a built-in niche
A new concrete driveway with a paver border
A stone counter, tile backsplash and open shelf after a kitchen remodel
A garage converted into a guest room and home office
New architectural shingles with a clean valley
A new casement window over a kitchen sink
Every visit starts with

Free written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled

We have financing partners for your dream remodel*On approved credit; ask us about your options
Get your free estimate

Boral Bathroom Remodeling: The Santa Rosa Owner’s Guide

Boral bathroom remodeling in Santa Rosa typically runs $9,000 – $28,000 installed, and the number depends mostly on which Boral product line you’re building around and how much of the wet area is being rebuilt at once. We give you that price in writing before any work starts, with a written scope and warranty attached, and we’re an independent contractor not affiliated with Boral. Most Santa Rosa owners don’t go looking for this page until something has already gone wrong: a hairline crack wandering across a floor tile, grout that keeps crumbling out of a shower joint no matter how many times it’s patched, or a vanity top that’s started to stain and dull within a few years of install. Boral covers a lot of ground in a bathroom (tile, engineered stone, trim, masonry), so the first job is figuring out exactly which product you have and what failed.

Call (833) 842-1866

Which Boral Models This Applies To

A tile setter installing wall tile in a shower

Boral makes a wide spread of bathroom products, and the part that matters changes depending on which one you own. On the tile side, you’re likely dealing with Boral’s porcelain or ceramic floor and wall lines, where the critical specs are the PEI wear rating and the coefficient of friction (COF) – the slip-resistance number that matters most on a bathroom floor. Boral engineered stone for vanity tops comes in slab and modular formats, and modular tops have fixed depth and width options that limit how much you can reconfigure without replacing the whole piece. Boral also produces trim and masonry products that show up around tub surrounds and exterior bathroom walls.

To identify what you have, check three things: a stamp or label on the back of a loose tile (Boral tile is usually marked with the series name and a shade/caliber code), the original invoice or builder paperwork if you have it, and a physical measurement of thickness and edge profile. The shade and caliber codes on tile are the compatibility gotcha most owners miss – two boxes from the same series and color can be from different caliber batches and won’t line up in thickness or tone, which is why a patch repair on Boral tile often shows a visible seam. For engineed stone, the OEM-versus-aftermarket decision is simpler: if it’s a modular vanity top, matching the original format is usually cheaper than modifying, and a fabricated replacement from a shop gives you a better fit than trying to retrofit a stock piece.

Explore

Styles & brands we work with

  • Kitchen remodeling
  • Bathroom remodeling
  • Home additions & ADU
  • Roofing
  • Windows & doors
  • Driveway & pavers
  • Fence

Signs Your Boral Bathroom Remodeling Is Failing

Boral tile and stone fail in predictable ways in Santa Rosa’s climate, where winter moisture and summer heat cycling work on a bathroom assembly year-round. Here’s what we see on inspection calls.

  • Hairline cracks across floor tiles. Usually the substrate flexing under a tile that was set over an inadequate or unsealed underlayment – common on older Santa Rosa homes where a bathroom was tiled directly over plywood without a proper isolation membrane.
  • Grout crumbling out of shower joints. Movement in the wall assembly or a failed waterproofing layer behind the tile, letting moisture reach the substrate. Patching the grout hides the symptom for a season and no more.
  • Tile popping or sounding hollow when tapped. A bond failure between tile and thinset, often from a slab or subfloor that moved after install. Hollow-sounding tile near a drain or shower pan is the one to take seriously.
  • Engineered stone vanity top staining or dulling. Surface etching from acidic cleaners or hard-water mineral buildup, or a factory finish that’s worn through. Some staining can be polished out; deep etching into the resin usually means replacement.
  • Loose or cracking trim and bullnose pieces. Adhesive failure at edges and corners, which lets water wick behind the tile field. A missing or cracked caulk joint at the tub-to-wall transition is the most common starting point.
Before & after

See the difference

Before - Recent ProjectBeforeAfter - Recent ProjectAfter
Recent Project
Before - Full RestorationBeforeAfter - Full RestorationAfter
Full Restoration
Before - Complete UpgradeBeforeAfter - Complete UpgradeAfter
Complete Upgrade

Replacement Cost & What’s Included

A new roof with clean valleys and new flashing

For a Boral bathroom remodel in Santa Rosa, the full scope lands at $9,000 – $28,000. A smaller bathroom (typically under 50 square feet of floor) runs $5,000 – $12,000. If the project centers on the shower, a walk-in shower install is $4,500 – $12,000, a tub-to-shower conversion is $3,500 – $10,000, and a straight shower replacement is $3,000 – $8,500. A vanity top install is $800 – $3,000. Here’s what moves the number within those ranges:

Scope Installed price range
Small bathroom remodel $5,000 – $12,000
Shower replacement $3,000 – $8,500
Tub-to-shower conversion $3,500 – $10,000
Walk-in shower installation $4,500 – $12,000
Vanity installation $800 – $3,000
Full bathroom remodel $9,000 – $28,000

The biggest cost drivers are whether the waterproofing layer needs to be rebuilt (it usually does on a failed shower), tile size and format, and slab versus modular stone. Part and labor are quoted as separate lines so you can see exactly what you’re paying for. Every visit includes a documented photo record of what we found and what was done, and the work is covered by our 365-Day Done Right Promise: if it’s not done right, we make it right.

DIY or Call Us?

Some things are safe to check yourself: tap tiles with a screwdriver handle to find hollow spots, measure tile thickness and look for a label or stamp, check the caulk line at the tub-to-wall joint for cracks, and photograph any crack or stain before it spreads. What you don’t want to do yourself is tear out a shower wall or re-grout over failing waterproofing – pulling tile off a failed shower membrane is how a surface problem becomes a full rebuild once moisture has already reached the substrate. Setting tile over a substrate that’s still moving, or resealing a shower without addressing the waterproofing, just resets the clock. If the tile is hollow, the grout keeps failing, or water is getting behind the surface, that’s the point to bring in a professional. We’ll tell you what we found in plain terms and put the price in writing before anything comes apart. Call (833) 842-1866 for a free estimate, and if you have a competitor’s quote we’ll review it line by line at no charge. We also install and service KraftMaid, Cambria, and Silestone products alongside Boral.

FAQs

A new multi-panel patio door opening a kitchen to the patio

How long does Boral bathroom tile last?
Boral porcelain and ceramic tile will last decades under normal conditions – the tile itself rarely fails. What fails is the assembly around it: the waterproofing, the grout, and the substrate. In Santa Rosa’s wet winters, a shower that isn’t properly waterproofed behind the tile can start showing grout failure within 5 – 10 years even though the tile is fine.

Can I repair a failing Boral bathroom instead of replacing everything?
Sometimes, yes. A single cracked tile over a solid substrate can often be replaced, and mild etching on engineered stone can be polished out. But if the cracks are spreading, tile sounds hollow, or grout keeps failing after repatching, the waterproofing or substrate is the real problem and a patch won’t hold. Call (833) 842-1866 and we’ll tell you which you’re dealing with before you pay for a repair that won’t last.

How long does a Boral shower or vanity replacement take?
A vanity top swap is typically a one-day job. A shower replacement with new waterproofing runs several days to a couple of weeks depending on how much demo and substrate repair is needed. We give you the timeline in the written scope before work starts. Call (833) 842-1866 for a free estimate.

How do you source the right Boral part?
We start from the labels, shade and caliber codes, and measurements on your existing materials, then match to the current Boral line or a compatible replacement. Because we work across fifty-plus vetted material brands, we can find a match or a better-fit substitute rather than forcing an exact discontinued piece. Bring us your photos and we’ll review the options line by line – estimates are free at (833) 842-1866.

When a Boral bathroom in Santa Rosa needs work, start with a written price and a documented scope before anyone picks up a tool. Call Rowan Construction Group at (833) 842-1866 to schedule your free estimate, and bring a competitor’s quote if you have one – we’ll review it line by line at no charge.

Written by the team at Rowan Construction Group Santa Rosa, serving Santa Rosa and nearby areas.

Ideas for every part of the house

Kitchens, baths, roofs, windows, fences and patios: the projects that make a house work better inside and out.

Read our project guides
A new white vinyl privacy fence with a double gateNew painted shaker cabinets with an organized deep drawerA remodeled kitchen with a waterfall island and wood cabinetsA finished backyard cottage with a small covered porchA new stained cedar privacy fenceA new paver patio with a seat wall and fire pit

Explore more projects

Every project below starts the same way: a free on-site visit and a written price.

Getting started with Rowan in Santa Rosa

Every project starts with a conversation and a written price. Here is how to take the first step.

A project lead walking the house with the homeowner during a free estimate

Free on-site estimate

A project lead walks the job with you, measures it and hands you a written, line-item price. No obligation.

Book an estimate
A crew arriving at a home with materials and tools

Your Santa Rosa team

A local vetted partner works across Santa Rosa and the towns around it, to the same written standard as every Rowan job.

Areas we serve
A worker laying floor protection before work starts

Read our written promise

What we promise on every job, written down, with the terms spelled out before any work starts.

Our promise
Need Construction help nationwide? Licensed & insured · free written estimates
Call (833) 842-1866
Local Service Coverage

Request a Free Estimate in Santa Rosa

Tell us what you need - Rowan Construction Group Santa Rosa responds fast. No obligation.

By submitting this form you agree to our Privacy Policy and consent to be contacted by phone, email or SMS about your request, including by local professionals who may handle it.

Prefer to text? Send a Text
Call Now - 24/7 Dispatch