A Rowan company - serving Santa Rosa, CA
A backyard with a new horizontal privacy fence
Jerith · Santa Rosa

Jerith Driveway & Pavers in Santa Rosa, CA

Free Estimate on SiteCalls Answered by a Live Person, 24/7Background-Checked TechniciansA Local Team in Santa Rosa
A new white vinyl privacy fence with a double gate
A new stained cedar privacy fence
A finished backyard cottage with a small covered porch
A new roof with clean valleys and new flashing
A new multi-panel patio door opening a kitchen to the patio
A new paver patio with a seat wall and fire pit
A remodeled primary bathroom with a soaking tub and walk-in shower
A single-story rear room addition with tall windows and a new patio
Every visit starts with

Free written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled

We have financing partners for your dream remodel*On approved credit; ask us about your options
Get your free estimate

Jerith Driveway & Pavers: The Santa Rosa Owner’s Guide

Jerith products in Santa Rosa are almost always aluminum ornamental fencing, gates and hardscape-adjacent systems rather than pavers themselves, so when an owner calls us about a “failed Jerith driveway” they usually mean the aluminum border fence, gate or edge restraint that frames a paver or concrete apron. Installed repair and replacement work in Santa Rosa runs $400 – $1,800 for a section of fence or a single gate, and full paver driveway work sits at $7,000 – $18,000 depending on square footage and base depth. We’re an independent contractor, not affiliated with Jerith, and we’ve seen every failure mode these parts produce in Sonoma County’s clay soils and wet winters.

Call (833) 842-1866

Owners typically discover the failure the same way: a gate starts dragging on the drive, a post wobbles after the first hard rain, or a run of aluminum pickets near the apron goes chalky and loose at the fasteners while the rest of the yard’s fencing looks fine. That last detail matters, because driveway-adjacent Jerith sections take splash, tire spray and gutter discharge that inland fence runs never see.

Key Takeaways

  • Jerith makes aluminum fencing, gates and rails, not pavers; the “driveway” failure is usually border fence, gate or edge restraint damage.
  • Section repairs run $400 – $1,800; full paver driveways $7,000 – $18,000 in Santa Rosa.
  • Failing gates and loose posts on clay soil are the two most common winter call-outs near driveways.
  • Aluminum doesn’t rot, but fasteners, hinges and base plates do, and they fail first.

Which Jerith Products This Applies To

A new front yard fence with a matching gate

Jerith’s residential line is built around aluminum ornamental fence panels, gate assemblies and matching posts, sold in named series with different rail profiles and picket spacings. Driveway-adjacent installations typically use a heavier gate style with a welded frame and a self-closing hinge rated for a wider swing, and pickup that weight matters. If your gate sags within a season, the hinge and post footing are usually the culprit long before the aluminum itself is.

Identifying the right replacement part starts with the post cap and the rail profile, not the color. Take a photo of the hinge plate, the latch, and the underside of the bottom rail, then measure post-to-post spacing at ground level and the actual gate width. Jerith has changed picket spacing and rail dimensions across its product generations, so a hinge that fits a current-era gate may not line up on an older one. That’s a compatibility gotcha we hit often: a customer brings a hardware kit from a big-box shelf that threads into a current post bracket but sits a half-inch off on a ten-year-old panel.

The OEM-versus-aftermarket call is honest and simple. For structural aluminum components – a post, a panel, a welded gate frame – stay with the Jerith-spec part, because the metal gauge and powder coat matter over a decade in coastal weather. For hinges, latches and self-closing hardware, a quality aftermarket equivalent from a name manufacturer performs as well and costs less. We source from over fifty vetted brands across trades, and we’ll tell you which side of that line a given part falls on. Our technicians have up to 19 years of experience matching hardware to older systems.

Explore

Styles & brands we work with

  • Kitchen remodeling
  • Bathroom remodeling
  • Home additions & ADU
  • Roofing
  • Windows & doors
  • Driveway & pavers
  • Fence

Signs Your Jerith Driveway & Pavers Is Failing

  • The gate drags or scrapes the drive. That’s a hinge pin worn flat or a post footing that settled after the soil shifted. In Santa Rosa’s clay, a wet winter pushes a footing out of plumb before the aluminum shows any damage.
  • A post wobbles when you push it. The concrete collar under the post has cracked, often because it was poured too shallow or the original installer set the post in dirt rather than a proper footing. A wobble always precedes a lean.
  • Fasteners are loose, stripped or rusted at the base. Aluminum won’t rust, but the steel bolts and self-tapping screws holding panels and brackets will, especially where driveway splash keeps them wet. Once the threads strip, the joint opens up.
  • The powder coat is chalking or peeling near the apron. Tire spray, gutter discharge and the de-icing salt some owners still use accelerate coating failure at the bottom rail. Coating loss exposes bare aluminum to staining and pitting.
  • The latch won’t catch consistently. A latch that misses means the gate has dropped or the post flexed, which points back to a footing or hinge issue rather than the latch itself.

Paver-related failures near these aluminum runs usually trace to base washout along the edge restraint, where water flowing off the drive scours out the compacted sub-base. That shows as a single sunken course of pavers along the border.

Before & after

See the difference

Before - Recent ProjectBeforeAfter - Recent ProjectAfter
Recent Project
Before - Full RestorationBeforeAfter - Full RestorationAfter
Full Restoration
Before - Complete UpgradeBeforeAfter - Complete UpgradeAfter
Complete Upgrade

Replacement Cost & What’s Included

A new curved paver walkway to the front porch

Here’s how the numbers land in Santa Rosa, and we put the range in writing before anyone picks up a tool:

Work Installed range
Fence or gate section repair $400 – $1,800
Full driveway replacement $5,000 – $14,000
Paver driveway installation $7,000 – $18,000
Concrete driveway installation $4,500 – $12,000
Driveway sealing $250 – $700
Paver patio installation $3,500 – $11,000

The range is driven by post count, footing depth, gate complexity, whether the existing footing has to be dug out, and total square footage on paver work. Parts and labor are itemized separately in the quote so you can see what the aluminum hardware costs versus the digging, footing and install time. Under Clause 1 of The Haven Standard, the price is written before anyone starts, and nothing about the scope changes without a signed change order. The work carries our 365-Day Done Right Promise.

DIY or Call Us?

Some things are safe to check yourself. Tighten a visible hinge screw, clear debris from a gate track, and take photos of the failures. What goes wrong with DIY on this specific work is the footing. A post that wobbles in clay soil needs the old collar dug out and a proper footing poured at the right depth – and a gate assembly is heavy enough that a dropped post can swing and land on a person or a car. We recommend a trained crew for any post work, footing work, or gate frame swap. The aluminum itself is light; the footing that holds it is not a weekend job.

Call us at (833) 842-1866 for a free estimate, or bring a competitor’s quote and we’ll review it line by line at no charge.

Frequently Asked Questions

A galley kitchen opened up to the dining room with a new peninsula

Ideas for every part of the house

Kitchens, baths, roofs, windows, fences and patios: the projects that make a house work better inside and out.

Read our project guides
A garage converted into a guest room and home officeA new clay tile roofNew double-hung windows in a dining roomA new paver pool deckAn open kitchen and dining area after a remodelA freestanding soaking tub in a remodeled primary bathroom

Explore more projects

Every project below starts the same way: a free on-site visit and a written price.

Getting started with Rowan in Santa Rosa

Every project starts with a conversation and a written price. Here is how to take the first step.

A project lead walking the house with the homeowner during a free estimate

Free on-site estimate

A project lead walks the job with you, measures it and hands you a written, line-item price. No obligation.

Book an estimate
A crew arriving at a home with materials and tools

Your Santa Rosa team

A local vetted partner works across Santa Rosa and the towns around it, to the same written standard as every Rowan job.

Areas we serve
A worker laying floor protection before work starts

Read our written promise

What we promise on every job, written down, with the terms spelled out before any work starts.

Our promise
Need Construction help nationwide? Licensed & insured · free written estimates
Call (833) 842-1866
Local Service Coverage

Request a Free Estimate in Santa Rosa

Tell us what you need - Rowan Construction Group Santa Rosa responds fast. No obligation.

By submitting this form you agree to our Privacy Policy and consent to be contacted by phone, email or SMS about your request, including by local professionals who may handle it.

Prefer to text? Send a Text
Call Now - 24/7 Dispatch