







Free written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
ES Windows Windows & Doors: The Santa Rosa Owner’s Guide
We install and service ES Windows-compatible windows and doors in Santa Rosa, with most full window replacement landing between $4,500 and $15,000 installed, and impact-rated units running $8,000 to $25,000. We work on ES Windows products as an independent contractor, not as an affiliated dealer. Owners usually find the problem the same way: a window that won’t latch shut in January, a door that drags on its threshold by spring, or fog between the panes that never clears no matter how warm the afternoon gets.
Which ES Windows Models This Applies To

ES Windows has made aluminum and vinyl products for decades, and the parts that fail first – rollers, sash balances, weatherstripping, glazing gaskets, lock hardware – are specific to the series and the year it was built. Two units that look identical from the curb can take completely different hardware. That’s the trap most homeowners hit when they order a replacement part online and it arrives close but not right.
The identification steps that actually work:
- Find the label. ES Windows prints a label in the head jamb or the frame channel on most sliding and hung units. It lists the series and a production code. If it’s faded, photograph it under a flashlight and compare against the parts sheet.
- Measure the operating hardware, not the glass. Roller diameter, balance channel length, and lock keep spacing are the three numbers that decide fit. A 1/16-inch difference in a pivot shoe means the sash won’t seat.
- Match the vintage. Aluminum series from the 1980s and 1990s often used a different roller assembly than the vinyl lines that followed. Aftermarket equivalents exist for most of these and hold up fine – but only when the spec matches. On older ES units we frequently find that a generic aftermarket roller’s housing is 2mm taller than the OEM part, and the sash rides proud of the track.
Where OEM is the right call: any part under tension, any lock or latch on an egress window, and anything on an impact-rated unit where the rating depends on the assembly staying intact. Where a quality aftermarket equivalent works: rollers, screen hardware, and most weatherstripping.
Styles & brands we work with
- Kitchen remodeling
- Bathroom remodeling
- Home additions & ADU
- Roofing
- Windows & doors
- Driveway & pavers
- Fence
Signs Your ES Windows Windows & Doors Is Failing
- The sash won’t stay up. The block-and-tackle or spiral balance has lost tension. On a hung window this is a balance replacement, not a sash replacement, and it’s often a 20-minute job once the right part is on hand.
- The slider is stiff or jumps the track. Rollers have flat-spotted or the track has debris and a bent lip. Santa Rosa’s summer dust and winter grit work into the bottom track, and a roller that’s been grinding for two seasons usually needs replacement rather than cleaning.
- Fog or condensation between the panes. The insulated glass unit’s perimeter seal has failed. This one can’t be repaired with a sealant – the IGU gets replaced, and on an impact-rated ES unit the replacement glass has to carry the same rating as the original.
- The door drags on the threshold or the frame. Settling or a worn hinge and closer combination. In Santa Rosa’s clay-heavy soils, we see this most on doors facing the afternoon sun, where thermal movement adds to the problem.
- You can feel air at the frame on a windy evening. Weatherstripping has compressed or the glazing gasket has pulled away. It’s the cheapest fix on this list and the one most often deferred until the heating bill notices.
See the difference
Before
After
Before
After
Before
AfterReplacement Cost & What’s Included

Here’s what window and door work runs in Santa Rosa, quoted as a flat written price with a written scope before anyone starts:
| Work | Installed range |
|---|---|
| Window replacement (per scope) | $4,500 – $15,000 |
| Impact window installation | $8,000 – $25,000 |
What moves the number: unit count, whether it’s a like-for-like swap or a re-frame, glass spec (tempered, laminated, impact), and whether the opening needs trim or stucco repair after removal. Hardware and parts are line-itemed separately from labor so you can see exactly what you’re paying for. Every job carries our 365-Day Done Right Promise – if it isn’t done right, we make it right – and every visit includes a documented photo record of what we found and what we did. We also offer a Free Second Opinion on any written estimate: bring a competitor’s quote and we’ll review it line by line at no charge.
DIY or Call Us?
You can safely check a few things yourself: clean the bottom track, confirm the label and series number, measure roller diameter and lock spacing, and test whether the sash moves freely with the hardware removed. What goes wrong on DIY is the part match – ordering a roller or balance that’s visually close but dimensionally off, then forcing it into the frame and cracking a sash channel or bending a track lip. That turns a $40 part into a full unit replacement. If you’re dealing with an impact-rated assembly or a door that isn’t latching, stop and call us at (833) 842-1866 – a trained technician can identify the ES Windows part on site and give you a written price before any work begins.
FAQs

Balances and rollers typically last 10 to 20 years before they need replacement; weatherstripping often goes 8 to 12. Santa Rosa’s dry summers and wet winters accelerate gasket wear on south-facing units more than most owners expect. Call (833) 842-1866 for an exact quote – estimates are free.
Sometimes. Rollers and balances are replaceable components, and a stiff slider is often a roller swap rather than a whole-unit job. Fogged insulated glass can’t be repaired and needs a new IGU. We’ll tell you which case you’re in before quoting.
A hardware or balance replacement on an ES Windows unit is usually a few hours; a full window replacement is scheduled across a longer window depending on unit count. We confirm timing in writing with your quote.
By matching the series label, production code, and physical measurements against our vendor network – we don’t carry stock and we don’t guess. If OEM is unavailable, we identify a spec-matched aftermarket equivalent and tell you plainly which one we’re using. We also service KraftMaid, Cambria, and Silestone products. Call (833) 842-1866 to schedule your free estimate and get a written price before work starts.
Written by the team at Rowan Construction Group Santa Rosa.












