







Free written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
CGI Kitchen Remodeling: The Santa Rosa Owner’s Guide
This page matches parts to a CGI kitchen. To be clear about what CGI sells and what we do: CGI makes cabinets, and we install CGI cabinets and the parts that support them – hinges, drawer slides, and door fronts.
An installed CGI kitchen remodel in Santa Rosa runs $14,000 – $45,000. A cabinet-only refresh with new fronts and hardware is the bottom of that range, while a full gut with new boxes, counters, and backsplash sits at the top. A single replacement hinge or slide is a small job inside those numbers, and we quote it flat and written before any work starts.
Most Santa Rosa owners find out something failed before they shop for a replacement. A cabinet door starts dropping at one corner around Gladstone or Bennett Valley. A drawer sticks halfway out and never seats flush again. The soft-close hinge goes suddenly stiff, or the door swings past where it should stop. You notice it in passing for a week, then figure out it isn’t going to fix itself.
Which CGI Models This Applies To

CGI is a Canadian cabinet maker, and its North American lines run across framed, full-overlay, and frameless builds. The three things that determine which part you need are the box construction (framed with a face frame, or frameless with finished sides), the overlay type on the door (standard or full), and the cabinet depth and height.
Don’t guess. Open the cabinet door and look at the inside of the door itself, or the underside of the top rail, for a manufacturer label. That label carries the model code and sometimes the hardware spec. If there’s no label, measure the face of the cabinet and the corner where the door mounts. A 3/8-inch reveal isn’t the same part as a full overlay.
The OEM-versus-aftermarket decision for CGI is usually clear. A hinge or slide with the CGI spec is a straight swap and matches the hole pattern. A quality aftermarket equivalent from Blum or Hettich fits the same opening, costs less, and often carries a stronger spring. What matters more than brand is the measurement: hinge cup diameter, cup depth, overlay, and slide length in inches. Get those four numbers right and the part fits.
Styles & brands we work with
- Kitchen remodeling
- Bathroom remodeling
- Home additions & ADU
- Roofing
- Windows & doors
- Driveway & pavers
- Fence
Signs Your CGI Kitchen Remodeling Is Failing
Each of these has a specific cause you can verify once the part is off.
- Cabinet door sags at the hinge. The screws have pulled out of the wood at the cup, or the hinge arm has bent. On older CGI boxes the screw holes widen over time, and the fix is either a repair insert or a new hinge in a fresh hole.
- Soft-close stops working. The hydraulic damper inside the hinge has dried out. It’s a hard failure, not a slow one, and it doesn’t come back once it’s gone.
- Drawer sticks or won’t close flush. A drawer slide that’s lost its ball bearings or bent a rail. Pull the drawer straight out and look at the rail; if the race is deformed, the slide is done.
- Door won’t stay closed or opens itself. The hinge spring has weakened, or the door is out of alignment against the adjacent cabinet. In a full-overlay CGI build, one misaligned door can push the next.
- Wood or finish crumbling around the hinge cup. Moisture intrusion, common in Santa Rosa kitchens with west-facing windows where morning condensation collects on the frames. A new hinge won’t hold in soft wood; the hole needs a proper repair first.
See the difference
Before
After
Before
After
Before
AfterReplacement Cost & What’s Included

We name the price in dollars before we lift a tool, and this page lists the ranges we work from in Santa Rosa. A single hinge or slide replacement is small. A batch of doors, hardware, and new slides sits inside the cabinet installation range. A full kitchen with new CGI boxes, counters, and backsplash runs the full lead range.
| Work | Installed range in Santa Rosa | What’s included |
|---|---|---|
| Hinge and slide replacement, per cabinet | Quoted per job | New hardware matched to CGI spec, install, alignment check |
| Cabinet installation (CGI boxes and fronts) | $4,000 – $13,000 | Boxes, doors, hardware, install, level and shim |
| Countertop installation | $2,000 – $6,500 | Template, install, seam set, backed by our 365-Day Done Right Promise |
| Backsplash installation | $800 – $2,500 | Layout, set, grout |
| Kitchen island installation | $3,000 – $10,000 | Island build, toe kick, install |
| Full kitchen remodel | $14,000 – $45,000 | Scope written line by line, no change order without your signature |
What drives the range: the number of cabinets affected, whether the boxes are still sound, and whether the counters need removal to reach the hinges on upper cabinets. Every line is broken out, parts and labor separately, so you can see what the hardware costs and what the install costs. No work starts under Clause 1 of the Haven Standard until you have the written price in hand, and if a change is needed mid-job, nothing proceeds until you sign the change order.
DIY or Call Us?
A homeowner can safely tighten a loose hinge screw with a screwdriver, confirm the label inside the door, and pull a drawer out to inspect the slide. Those three checks cost nothing and often tell you exactly what needs replacing.
What goes wrong is the swap itself. The cabinet door is heavy, the hinge cup hole is specific, and a new hinge seated in a soft or damaged hole will pull out again in a month. Getting the overlay wrong means the door sits proud or binds against the next one. Repairing the cabinet side for a stripped screw hole needs an insert set and a clamp, and if the boxes are damaged by moisture, a new hinge won’t hold at all. If your cabinet door has dropped and the box feels soft, call us first. We’ll tell you if a repair will hold or if the box needs more. You can also bring a competitor’s quote and we’ll review it line by line, no charge.
For the part or the full kitchen, call (833) 842-1866 for a free estimate. We’re an independent service provider in Santa Rosa, not affiliated with CGI, and we install CGI cabinets along with KraftMaid, Cambria, and Silestone as part of a full kitchen scope.
FAQs

A quality soft-close hinge lasts 10 to 15 years in a normal kitchen, and a drawer slide lasts about the same. In Santa Rosa, morning condensation on west-facing kitchen windows shortens that on the cabinets nearest the glass, sometimes by four or five years, because moisture softens the wood around the hinge cup and the screws lose their grip. If your hardware is past the 10-year mark and the doors are drifting, that’s the expected lifespan, not a defect. Call (833) 842-1866 for a flat written quote on replacement. Estimates are free.
Sometimes. A loose hinge screw with sound wood behind it can be repaired with an insert, and that’s a genuine fix. A dried-out soft-close damper or a slide with a deformed rail can’t be repaired and has to be replaced. If the cabinet side is soft or crumbled around the hinge cup, a repair won’t hold and new hardware won’t either; the hole needs to be rebuilt or the box replaced. We’ll tell you which case you’re in after we look, and the written price comes before any work. Call (833) 842-1866 for an exact quote.
A single hinge replacement is under an hour. A batch of doors with new hinges and slides across a typical Santa Rosa kitchen takes a few hours. A cabinet installation with new CGI boxes runs a few days, and a full kitchen remodel with counters and backsplash runs several weeks. The written quote we give you spells out the schedule line by line. Call (833) 842-1866 to schedule your free estimate.
We source to the spec, not to a hunch. We pull the model code from the label inside the cabinet door, then measure the hinge cup diameter, cup depth, overlay, and slide length. With those four numbers we match the part to the CGI build, and if the exact OEM part isn’t available, we source a quality equivalent from Blum or Hettich that fits the same opening. We don’t stock parts and we don’t carry them on a truck, so we order to your cabinet’s spec. Call (833) 842-1866 and we’ll quote the part and the install together.
Call (833) 842-1866 to schedule your free estimate. We’ll match the part to your CGI cabinet, put the price in writing before anything starts, and hand you a documented photo record of what we found and what we did. Estimates are free and every project is backed by our 365-Day Done Right Promise.
Written by the team at Rowan Construction Group Santa Rosa, serving Santa Rosa and nearby areas.












