







Free written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Boral Driveway & Pavers: The Santa Rosa Owner’s Guide
We install Boral-compatible driveway and paver systems across Santa Rosa, and a full paver driveway typically runs $7,000 – $18,000 installed, with a paver patio at $3,500 – $11,000. Most Santa Rosa owners discover a failure the same way: a paver lifts after a wet winter, joints wash out along the slope, or a hairline crack opens across a driveway that looked solid in August. Boral makes clay and concrete pavers rather than a single “part,” so the real question is which Boral line you have and what failed – the unit, the bedding sand, or the base under it.
Key Takeaways
- Boral driveway and paver failures in Santa Rosa usually trace to the base and drainage, not the paver itself.
- Installed pricing runs $7,000 – $18,000 for a paver driveway and $3,500 – $11,000 for a patio.
- We’re an independent contractor, not affiliated with Boral, and we quote a flat written price before any work starts.
- Every visit includes a documented photo record, so you see what we found under the surface.
Which Boral Models This Applies To

Boral’s paver range splits into clay and concrete families, and the compatibility question matters because bedding and joint details differ between them. On the clay side you’ll run into Boral’s dry-pressed clay pavers, sold under lines like the Marlow and Sterling collections, plus the thinner clay units made for overlays. On the concrete side, Boral’s structural and permeable pavers carry different thickness specs, and a permeable system needs an open-graded base and a specific joint aggregate – not the mason sand used under a standard unit.
To identify what you have, pull one loose paver and read three things: the nominal thickness (2 3/8″ is common for standard concrete, clay runs thinner and denser), the color and texture match to the original, and any stamp or batch marking on the underside. Photograph it next to a tape measure before you call anyone. That single photo lets us match the replacement to your existing course instead of guessing at a dye lot that won’t match after two Sonoma County summers.
The OEM-versus-aftermarket call is straightforward here. When Boral still makes your line, we source the genuine unit so the color and dimension match the rest of the field. When a line is discontinued, a quality aftermarket paver in the same thickness is the honest answer, and we tell you plainly which one you’re getting before the written price goes out. If you’re pairing hardscape with a wider project, we also handle KraftMaid, Cambria and Silestone work on the interior side.
Styles & brands we work with
- Kitchen remodeling
- Bathroom remodeling
- Home additions & ADU
- Roofing
- Windows & doors
- Driveway & pavers
- Fence
Signs Your Boral Driveway & Pavers Is Failing
- Pavers lifting or rocking after rain. Water is sitting in the base because the subgrade wasn’t compacted or the fall is wrong, so the unit heaves. In Santa Rosa’s clay soils this shows up fast after the first real storm.
- Joint sand washing out along the slope. The joint aggregate is eroding because the surface drains toward the house instead of away from it. Re-sanding buys time, but the grade is the actual cause.
- Hairline cracks across a paver. A single cracked unit usually means point-loading from an uneven base beneath it, not a bad paver. Replacing the one piece without fixing the bed cracks the next one.
- Settling at the driveway apron or garage threshold. The transition to concrete or the slab edge has lost support, which is common where a driveway meets an older pour. It’s a base repair, not a paver swap.
- Efflorescence and dark damp patches that don’t dry. White mineral bloom and persistent moisture mean water is trapped under the system. Left alone, that’s how a paver field starts to fail from the bottom up.
See the difference
Before
After
Before
After
Before
AfterReplacement Cost & What’s Included

Installed pricing in Santa Rosa sits in these ranges, and we put the number in writing before anything moves:
| Work | Installed range |
|---|---|
| Paver driveway installation | $7,000 – $18,000 |
| Paver patio installation | $3,500 – $11,000 |
| Driveway replacement | $5,000 – $14,000 |
| Driveway sealing | $250 – $700 |
| Concrete driveway installation (comparison) | $4,500 – $12,000 |
What drives the range: square footage, whether the base needs full excavation or just re-compaction, the paver line you choose, and slope or drainage corrections. Under Clause 1, the price is written before anyone starts, and no change proceeds without a signed change order. So you’ll see parts and labor broken out, not bundled into a number you can’t question. Every job carries our 365-Day Done Right Promise, backed by The Haven Standard.
DIY or Call Us?
You can safely check a few things yourself: lift one loose paver and photograph it with a tape measure, note where water pools after rain, and confirm the paver thickness. That’s diagnosis, not repair.
Where DIY goes wrong is the base. A paver field is only as good as the compacted subgrade and the drainage fall beneath it, and getting that wrong means the new surface fails the next wet season. Excavation, base prep and re-grading are real earthwork, and a homeowner resetting units over a soft bed is the most common reason a repair comes back. If a paver has shifted or the joints won’t hold, call us at (833) 842-1866 for a free estimate and we’ll show you what’s under it in the photo record.
FAQs

The pavers themselves often last decades, but the system lifespan depends on the base and drainage. In Santa Rosa’s clay-heavy soils, a poorly drained base can fail within a few years while a correctly built one holds for the long run. Call (833) 842-1866 for an exact quote – estimates are free.
Often yes. If only a section has settled or the joints washed out, we can lift, re-grade and reset the affected area without tearing out the whole field. Full replacement makes sense when the base is failing across the driveway. We give you the honest split before quoting.
A localized reset is typically a day or so, while a full driveway replacement usually runs several days depending on size and base work. We confirm the timeline in the written scope before work starts.
We match to your existing unit by thickness, color and underside markings from the photo you provide, sourcing genuine Boral where the line is current and a matched aftermarket equivalent where it’s discontinued. “Call for a quote” isn’t how we work – you get a flat written price with the part named.
If your Boral driveway or pavers are showing any of these signs, the fastest path to a real number is a call. We’ll review a competitor’s written estimate line by line at no charge with our Free Second Opinion, and hand you a flat written price before any work begins. Call Rowan Construction Group Santa Rosa at (833) 842-1866 to schedule your free estimate.
Written by the team at Rowan Construction Group Santa Rosa, serving Santa Rosa and nearby areas.












