







Free written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Boral Fence Installation: The Santa Rosa Owner’s Guide
Boral fence installation in Santa Rosa typically runs $3,500 to $9,000 installed, and most projects are completed over two to four scheduled days once materials are on hand. We work with independent local crews who install Boral-compatible systems and quote a written flat price before anything gets dug. Owners usually find out a fence is failing the same way: a post leans after a wet winter, a panel sags between rails, or a gate that closed cleanly last spring starts dragging on the concrete.
Santa Rosa sits on clay-heavy soils in many of its older neighborhoods, and that matters for fencing. Clay swells when the rain comes and shrinks in the dry months, and a post set in a shallow concrete collar will work loose in a single season. If you’re staring at a wobbly fence and wondering whether it’s the post, the rail, or the whole run, this page walks through it in trade terms.
Key Takeaways
- Installed Boral fence runs $3,500 – $9,000 in Santa Rosa, depending on linear footage and gate count.
- Most failures trace to post footings and soil movement, not the fence boards themselves.
- We’re an independent contractor, not affiliated with Boral; we source compatible materials for the system you have.
- A written flat price and a documented photo record come standard on every job.
Which Boral Models This Applies To

Boral doesn’t make one fence. It makes fencing systems and components across several lines, and the material you have determines which parts are compatible. The two you’ll see most on Santa Rosa properties are Boral’s composite and timber-look fence systems (marketed under names like Boral Fencing and its associated panel and post components) and Boral masonry and retaining-wall block where a fence ties into a garden wall. Before we quote, we identify the system by reading the manufacturer stamp on the post cap or rail end where it’s visible, measuring the post cross-section (most residential posts run 4×4 or 5×5 nominal, and the exact dimension tells us the series), and checking the panel spacing center to center.
That measurement step is the compatibility gotcha most homeowners miss. A Boral post cap sized for one series won’t seat on another, and rail brackets rated for a specific rail profile won’t hold a different one. When the original part is discontinued or you can’t confirm it, we evaluate a quality aftermarket equivalent against the same load and dimension spec rather than forcing a mismatched OEM piece. We’ll tell you plainly which option we recommend and why.
Styles & brands we work with
- Kitchen remodeling
- Bathroom remodeling
- Home additions & ADU
- Roofing
- Windows & doors
- Driveway & pavers
- Fence
Signs Your Boral Fence Installation Is Failing
Fence problems show up in a specific order. Here’s what to look for and what’s actually happening underneath.
- Posts leaning or rocking. This is almost always a footing problem: the concrete collar is too shallow, the hole was dug narrow, or water is pooling at the base after our winter rains. The fence board isn’t the issue; the ground under it is.
- Panels sagging between rails. Sag comes from a rail that’s lost its fastener grip or a post that’s shifted slightly, dropping the rail out of level. Left alone, the sag loads the next rail down the line.
- Gates dragging or not latching. A gate is the highest-stress point on any fence because it moves. A hinge that’s loosened, or a post that’s settled a fraction of an inch, throws the whole swing off and puts strain on the latch hardware.
- Loose or popped fasteners. Rusted or backed-out screws and brackets let panels rattle and separate. In Santa Rosa’s wet-cool-dry cycle, cheap fasteners corrode faster than the fence material around them.
- Visible rot or soft spots at the base. Wood or timber-look components that stay damp at the ground line soften first. Probe the bottom six inches with a screwdriver; if it sinks easily, the material has given up.
See the difference
Before
After
Before
After
Before
AfterReplacement Cost & What’s Included

For a typical residential run, installed Boral fence work in Santa Rosa lands between $3,500 and $9,000. What drives the number up or down is linear footage, the number of gates, whether posts need new footings poured, and how much of the existing fence can be salvaged versus replaced outright. A repair on a few panels sits at the low end; a full replacement with new posts and a gate sits at the top.
| Scope | Typical installed range (Santa Rosa) |
|---|---|
| Panel and rail repair (partial run) | $3,500 – $5,000 |
| Mid-size replacement with new posts | $5,000 – $7,000 |
| Full run replacement including gate | $7,000 – $9,000 |
Our quote is a flat written price with a written scope and a written warranty, and the materials-plus-labor breakdown is on the page before you agree to anything. The work carries our 365-Day Done Right Promise. If it’s not right, we make it right.
DIY or Call Us?
You can safely check a few things yourself: confirm the post is the real problem by pushing it side to side, note whether the fasteners are corroded, and measure your post dimensions so you know which series you have. That’s information-gathering and it’s useful.
Where it goes wrong is the repair itself. Post footings are heavy, load-bearing, and need to be set to the right depth and diameter for the soil; a shallow re-set looks fine in July and fails by January. If your fence ties into a retaining wall or masonry block, moving a post can shift load onto structure that wasn’t designed for it. And replacing a run means getting panel alignment and fastener spec right the first time, or you’re back to a sagging fence within a season. We’d rather you call than hurt your back or your fence. Reach us at (833) 842-1866 for a written estimate.
FAQs

A well-installed Boral fence in Santa Rosa realistically gives you 15 to 20-plus years, and post footings are the deciding factor more than the fence material. Our wet winters and clay soils punish shallow footings, so a properly set post outlasts the boards around it. Call (833) 842-1866 if you want us to assess the footing depth on your run.
Often yes, if the posts are sound and only panels, rails, or hardware have failed, a targeted repair is the better spend. We confirm by checking post stability and footing condition first. If the posts are the problem, a partial repair just postpones the replacement. Call (833) 842-1866 and we’ll tell you which one you’re looking at.
Most residential Boral fence installs in Santa Rosa take two to four scheduled days once materials are on site, with a partial panel repair done in a single visit. Gate and footing work adds time. Call (833) 842-1866 to get a schedule estimate for your specific run.
We identify your system by post dimension and visible manufacturer markings, then source the compatible OEM part or a spec-matched equivalent. We don’t carry parts on a truck; the right component is ordered to the job. Call (833) 842-1866 and we’ll walk you through what we need to identify your fence.
We also work with KraftMaid, Cambria, and Silestone on other trades if you’re planning more than just fencing this year. For a written flat price on your Boral fence install in Santa Rosa, call (833) 842-1866 to schedule your free estimate. We’ll also review any competitor’s written quote line by line at no charge under our Free Second Opinion offer.
Written by the team at Rowan Construction Group Santa Rosa, serving Santa Rosa and nearby areas.












