







Free written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
IKO Windows & Doors: The Santa Rosa Owner’s Guide
We install and service IKO-compatible windows and doors across Santa Rosa, and installed whole-window replacement in this market typically runs $4,500 – $15,000 depending on count, frame condition and glazing, while impact-rated units land at $8,000 – $25,000. Same-day service applies to adjustments, hardware swaps, sealing and glazing repairs, not to full replacement, which is a scheduled job with a written price before we start. Most owners discover an IKO failure the same way: a bedroom that was never cold before stays cold after the first real Santa Rosa fog season, or a patio door starts dragging on the sill and the lock no longer lines up without lifting the handle.
Rowan Construction Group Santa Rosa is an independent contractor. We are not affiliated with IKO and we don’t manufacture, distribute or speak for IKO. What we can do is read your unit accurately, tell you which part it needs, and put the price in writing. If you also have KraftMaid, Cambria or Silestone work on your list, we handle those on the same written quote.
Key takeaways
- Whole-window replacement in Santa Rosa: $4,500 – $15,000. Impact-rated: $8,000 – $25,000.
- Hardware, sealing and glazing work almost always costs a fraction of replacement and is the right first call on a unit under 15 years old.
- Look for the certification label on the jamb or sash edge, not the marketing sticker on the glass. That’s the label the part number comes from.
- Our technicians have up to 19 years of experience, and calls are answered by a live person around the clock.
Which IKO Models This Applies To

IKO’s residential line is wide, and the part you need is dictated by the series, not by the house. Your identification path runs in this order: the certification or rating label fixed to the jamb or the top sash edge, then the frame dimensions measured at three points (top, middle, bottom – they will differ on any house older than the frame), then the glazing pattern and the operator hardware. Photograph all three before you call anyone. A part matched off a guess is a part that comes back.
The reason to lead with the label is a compatibility gotcha that catches Santa Rosa owners often: tilt-latch and balance assemblies designed for one sash weight series don’t transfer to a heavier impact-rated sash, and the part may seat and lock fine on the bench and fail within a season once the sash starts cycling. Sash weight is the spec range you need to confirm – a heavier unit running a standard balance will not hold an open position.
On the OEM-versus-aftermarket question, we source both ways and we’ll tell you which is honest for your case. OEM hardware is the right answer for anything under warranty or for a mechanism with a specific geometry – latch spacing, tilt-shoe profile, keeper offset. A quality aftermarket balance, sweep or weatherseal is often the same material at a lower number, and for consumables like weatherseal and glazing tape there is no argument for paying OEM. Our sourcing runs across more than fifty vetted brands, and that depth is what keeps the written price on your quote an honest number instead of a padded one.
Styles & brands we work with
- Kitchen remodeling
- Bathroom remodeling
- Home additions & ADU
- Roofing
- Windows & doors
- Driveway & pavers
- Fence
Signs Your IKO Windows & Doors Is Failing
- Drafts or cold spots at the jamb after sunset. Usually a compressed or shrunken weatherseal, or a corner weld that has pulled slightly. If you can see daylight at any point on the perimeter, the seal has failed rather than just aged.
- A sash that won’t stay up, or drops on its own. The balance assembly has lost tension or the spiral rod has snapped. This is a mechanical failure and it will not improve with use.
- Condensation between the panes. The insulated glass unit’s seal is gone, which means the argon is gone too. In Santa Rosa’s wet winters and dry summers, that thermal cycling is a real driver of IG unit failure.
- A patio door that drags, sticks or won’t latch without lifting. Either the roller has flat-spotted or the door has dropped in its frame from settlement. Left alone, the dragging edge wears the threshold and the lock hardware.
- Fogging, water staining or soft wood at the sill. This is the one to act on first. A sill taking on water is a substrate problem that can move into the framing, and Santa Rosa’s wet season gives it plenty of time to work.
Say what we found, not what we felt about it – that’s how our reports read. You’ll get the condition of the sill, the seal and the balance assembly in plain terms, plus a photo record of each, before any work is authorized.
See the difference
Before
After
Before
After
Before
AfterReplacement Cost & What’s Included

Window replacement in Santa Rosa runs $4,500 – $15,000. Impact window installation runs $8,000 – $25,000. The range moves on four things: the number of units, whether the frame is sound enough for a pocket or insert install versus a full-frame tear-out, the glazing package (tempered, low-E, impact-rated), and the finish.
| Scope | Installed price in Santa Rosa |
|---|---|
| Window replacement (insert or full-frame) | $4,500 – $15,000 |
| Impact-rated window installation | $8,000 – $25,000 |
| Single-unit hardware, balance or seal repair | Quoted per part, part plus labor, in writing |
Every number we give is a flat written price with a written scope and a written workmanship warranty. No change proceeds until you’ve signed a change order – that discipline is why our jobs finish within a few percent of the agreed cost. The quote breaks out parts and labor so you can see what you’re paying for. Bring a competitor’s estimate and we’ll review it line by line at no charge as your free second opinion.
DIY or Call Us?
Some of this work is genuinely safe to handle yourself, and we’d rather you knew which. You can check and clean the weep holes at the sill, replace a worn sweep or weatherseal on a patio door, adjust a roller height with the adjustment screw to stop a light drag, and clear any obstruction from a track. Replacing weatherstrip and re-seating a loose latch plate are also within reach for most owners with a screwdriver and patience.
Where it goes wrong: pulling a sash to get at a balance assembly, resetting an insulated glass unit, and tearing out a frame to cure a water-damaged sill. The balance systems and the heavy impact-rated sash carry real tension, and an assembly that slips under tension can take fingers and glass with it. On a second-floor unit that risks a fall as well. A failed sill is a substrate question underneath the window, which is where an honest inspection beats a web search every time. If we find rot under the frame, the price needs to reflect it before anyone picks up a tool.
Call (833) 842-1866 for a free estimate. Crews are background-checked and uniformed, and you’ll receive a documented photo record of every visit as a standard deliverable – not an add-on – backed by our 365-Day Done Right Promise.
FAQs

Expect 15-20 years for the unit itself before hardware and seal attention becomes routine, and 10-15 for an insulated glass unit before a seal failure shows. Santa Rosa’s swing between wet winters and dry, warm summers works the seals and the wood harder than a milder, steadier climate would. Call (833) 842-1866 for an inspection and a written opinion rather than replacing on age alone.
Often, yes. A failed balance, sweep, latch, weatherseal or roller is a hardware repair, and a fogged IG unit can be reglazed without replacing the frame. The line is the frame and sill: if the wood is soft or the weld has let go, replacement is the honest answer. Call (833) 842-1866 and we’ll tell you which side of that line you’re on before you spend anything.
A single hardware or balance repair is usually a short visit; a full window replacement is a scheduled job of one to several days depending on the unit count and whether we’re doing insert or full-frame work. We schedule replacement rather than promise same-day turnaround, because a frame that hasn’t been measured properly is a frame that comes back. Call (833) 842-1866 to get your job on the calendar with a written price in hand first.
From the certification label and the measurements, not from the marketing sticker. We read the label on the jamb or sash edge, measure the rough opening in three places, and confirm sash weight before ordering a balance – and we’ll tell you when an aftermarket equivalent is the better buy. Call (833) 842-1866 and send us photos of the label and the failure; we’ll come back with a written part-and-labor price.
Written by the team at Rowan Construction Group Santa Rosa, serving Santa Rosa and nearby areas.












